Effect of the CO<sub>2</sub> top-blowing ratio on the end of the converter

DONG Jian-feng; WEI Guang-sheng; ZHU Rong; DONG Kai; ZHANG Qing-nan; ZHANG Bing-long

doi:10.13374/j.issn2095-9389.2021.12.27.008

Volume 44 Issue 9

Sep. 2022

Turn off MathJax

Article Contents

Article Navigation > Chinese Journal of Engineering > 2022 > 44(9): 1476-1482

DONG Jian-feng, WEI Guang-sheng, ZHU Rong, DONG Kai, ZHANG Qing-nan, ZHANG Bing-long. Effect of the CO2 top-blowing ratio on the end of the converter[J]. Chinese Journal of Engineering, 2022, 44(9): 1476-1482. doi: 10.13374/j.issn2095-9389.2021.12.27.008

Citation:

DONG Jian-feng, WEI Guang-sheng, ZHU Rong, DONG Kai, ZHANG Qing-nan, ZHANG Bing-long. Effect of the CO₂ top-blowing ratio on the end of the converter[J]. Chinese Journal of Engineering, 2022, 44(9): 1476-1482. doi: 10.13374/j.issn2095-9389.2021.12.27.008

Citation:

PDF( 1298 KB)

Effect of the CO₂ top-blowing ratio on the end of the converter

doi: 10.13374/j.issn2095-9389.2021.12.27.008

DONG Jian-feng^{1, 2},
WEI Guang-sheng^{1, 2
,
,},
ZHU Rong^{1, 2},
DONG Kai^{1, 2},
ZHANG Qing-nan^{1, 2},
ZHANG Bing-long^{1, 2}

1.
School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing 100083, China
2.
Research Center for Carbon Dioxide, University of Science and Technology Beijing, Beijing 100083, China

More Information

Corresponding author: E-mail: wgshsteel@126.com
Received Date: 2021-12-27
Available Online: 2022-03-07
Publish Date: 2022-09-01

Abstract

Abstract

When combined with the high-temperature reaction characteristics of carbon dioxide—that is, the weak oxidation, endothermic, or weak exothermic effect compared with oxygen and the bubble increment effect of reacting with carbon to produce twice the gas—the carbon dioxide smelting process was targeted according to the different tasks in different periods of converter smelting. Before temperature measurement, sampling, and carbon determination using the sublance system, carbon dioxide is blown into the converter from the upper oxygen gun and the bottom blowing element of the converter. By changing the ratio of carbon dioxide and oxygen in the oxygen gun, an industrial experimental study was conducted on the effect of the carbon dioxide ratio blown from the upper oxygen gun on the endpoint of the mass fraction of phosphorus and nitrogen and the carbon–oxygen concentration product. The results show that with the gradual increase of the carbon dioxide top blowing ratio from 4.84% to 9.68% in the early and middle stages of converter smelting, the mass fraction of phosphorus at the end of the converter first decreases and then basically remains unchanged. The mass fraction of nitrogen also decreases gradually, but the decreasing range becomes smaller, and the changing trend of carbon–oxygen concentration product is the same as that of TFe in slag, which first decreases and then increases. The optimal carbon dioxide top-blowing ratio varies with the index. Furthermore, the test also shows that even if all the blown carbon dioxide reacts to generate additional carbon monoxide gas and the nitrogen is removed by the additional carbon monoxide gas generated compared with the original process, the partial pressure of nitrogen in the additional gas is much higher than the partial pressure in equilibrium with the mass fraction of nitrogen in the liquid steel. This indicates that the improvement of the denitrification effect is due to the additional gas generated by the reaction of blowing in carbon dioxide; it improves the denitrification effect of the original gas, and the generation of additional gas improves the kinetic conditions of the molten pool and facilitates the mass transfer of nitrogen. The highest decreasing ratio of the endpoint mass fraction of phosphorus, nitrogen, carbon–oxygen concentration product, and TFe in the slag of the test converter was 20.4%, 34.3%, 12.92%, and 8.89%, respectively.
- carbon dioxide,
- converter steelmaking,
- dephosphorization,
- denitrification,
- carbon–oxygen concentration product

FullText(HTML)

References(25)

References

[1]	呂明, 朱榮, 畢秀榮, 等. 二氧化碳在轉爐煉鋼中的應用研究. 北京科技大學學報, 2011, 33(增刊1): 126 Lü M, Zhu R, Bi X R, et al. Application research of carbon dioxide in BOF steelmaking process. J Univ Sci Technol Beijing, 2011, 33(Suppl 1): 126
[2]	王仲亮, 包燕平, 王達志, 等. 高磷轉爐渣中磷元素在不同酸中的浸出規律. 鋼鐵, 2021, 56(4):103 Wang Z L, Bao Y P, Wang D Z, et al. Leaching rule of phosphorus element in high phosphorus converter slag with different acids. Iron Steel, 2021, 56(4): 103
[3]	王林珠, 包燕平, 李翔. 轉爐留渣雙渣工藝兩階段脫磷對比. 鋼鐵, 2019, 54(8):37 Wang L Z, Bao Y P, Li X. Comparison of two-stage dephosphorization during remaining slag-double slag process in converter. Iron Steel, 2019, 54(8): 37
[4]	邢奕, 張文伯, 蘇偉, 等. 中國鋼鐵行業超低排放之路. 工程科學學報, 2021, 43(1):1 Xing Y, Zhang W B, Su W, et al. Research of ultra-low emission technologies of the iron and steel industry in China. Chin J Eng, 2021, 43(1): 1
[5]	林文輝, 焦樹強, 孫建坤, 等. 轉爐吹煉后期碳含量預報的改進指數模型. 工程科學學報, 2020, 42(7):854 Lin W H, Jiao S Q, Sun J K, et al. Modified exponential model for carbon prediction in the end blowing stage of basic oxygen furnace converter. Chin J Eng, 2020, 42(7): 854
[6]	魏光升, 韓寶臣, 朱榮. CO₂作為RH提升氣的冶金反應行為研究. 工程科學學報, 2020, 42(2):203 Wei G S, Han B C, Zhu R. Metallurgical reaction behavior of CO₂ as RH lifting gas. Chin J Eng, 2020, 42(2): 203
[7]	Feng C, Zhu R, Liu R Z, et al. Industrial application of bottom-blown CO₂ in basic oxygen furnace steelmaking process. Steel Res Int, 2021, 92(10): 2000704 doi: 10.1002/srin.202000704
[8]	Li Z, Zhu R, Ma G, et al. Laboratory investigation into reduction the production of dust in basic oxygen steelmaking. Ironmak Steelmak, 2017, 44(8): 601 doi: 10.1080/03019233.2016.1223906
[9]	李智崢, 朱榮, 劉潤藻, 等. 煉鋼過程底吹氣體的冶煉效果對比. 鋼鐵, 2016, 51(9):40 Li Z Z, Zhu R, Liu R Z, et al. Comparison of smelting effects by bottom blowing different gases. Iron Steel, 2016, 51(9): 40
[10]	靳任杰, 朱榮, 馮立新, 等. 二氧化碳-氧氣混合噴吹煉鋼實驗研究. 北京科技大學學報, 2007, 29(增刊1): 77 Jin R J, Zhu R, Feng L X, et al. Experimental study of steelmaking with CO₂ and O₂ mixed blowing. J Univ Sci Technol Beijing, 2007, 29(Suppl 1): 77
[11]	尹振江, 朱榮, 易操, 等. 應用COMI煉鋼工藝控制轉爐煙塵基礎研究. 鋼鐵, 2009, 44(10):92 doi: 10.3321/j.issn:0449-749X.2009.10.021 Yin Z J, Zhu R, Yi C, et al. Fundamental research on controlling BOF dust by COMI steel-making process. Iron Steel, 2009, 44(10): 92 doi: 10.3321/j.issn:0449-749X.2009.10.021
[12]	李智崢, 朱榮, 劉潤藻, 等. CO₂的高溫特性及對煉鋼物料和能量的影響研究. 工業加熱, 2015, 44(6):27 doi: 10.3969/j.issn.1002-1639.2015.06.007 Li Z Z, Zhu R, Liu R Z, et al. Study on the characteristics of CO₂ and the effect of CO₂ on material and energy in steelmaking process. Ind Heat, 2015, 44(6): 27 doi: 10.3969/j.issn.1002-1639.2015.06.007
[13]	張偉, 李智崢, 朱榮, 等. 煉鋼過程噴吹CO₂的實驗研究. 工業加熱, 2015, 44(2):41 doi: 10.3969/j.issn.1002-1639.2015.02.012 Zhang W, Li Z Z, Zhu R, et al. Experimental study of CO₂ blowing in steelmaking process. Ind Heat, 2015, 44(2): 41 doi: 10.3969/j.issn.1002-1639.2015.02.012
[14]	Yi C, Zhu R, Chen B Y, et al. Experimental research on reducing the dust of BOF in CO₂ and O₂ mixed blowing steelmaking process. ISIJ Int, 2009, 49(11): 1694 doi: 10.2355/isijinternational.49.1694
[15]	Zhu R, Bi X R, Lv M, et al. Research on steelmaking dust based on difference of Mn, Fe and Mo vapor pressure. Adv Mater Res, 2011, 284-286: 1216 doi: 10.4028/www.scientific.net/AMR.284-286.1216
[16]	易操, 朱榮, 尹振江, 等. 基于30t轉爐的COMI煉鋼工藝實驗研究. 過程工程學報, 2009, 9(增刊1): 222 Yi C, Zhu R, Yin Z J, et al. Experimental research of COMI steelmaking process based on 30 t converter. Chin J Process Eng, 2009, 9(Suppl 1): 222
[17]	寧曉鈞, 尹振江, 易操, 等. 利用CO₂減少煉鋼煙塵的實驗研究. 煉鋼, 2009, 25(5):32 Ning X J, Yin Z J, Yi C, et al. Experimental research on dust reduction in steelmaking by CO₂. Steelmaking, 2009, 25(5): 32
[18]	Lv M, Zhu R, Wei X Y, et al. Research on top and bottom mixed blowing CO₂ in converter steelmaking process. Steel Res Int, 2012, 83(1): 11 doi: 10.1002/srin.201100166
[19]	張家蕓. 冶金物理化學. 北京: 冶金工業出版社, 2004 Zhang J Y. Physical Chemistry of Metallurgy. Beijing: Metallurgical Industry Press, 2004
[20]	劉躍, 劉瀏, 佟溥翹, 等. 優質高碳鋼高拉碳前期脫磷過程控制. 煉鋼, 2006, 22(2):27 doi: 10.3969/j.issn.1002-1043.2006.02.009 Liu Y, Liu L, Tong P Q, et al. Process control of dephosphorization in initial smelting period of combined blowing BOF for clean steel. Steelmaking, 2006, 22(2): 27 doi: 10.3969/j.issn.1002-1043.2006.02.009
[21]	李智崢. CO₂應用于煉鋼的基礎理論研究[學位論文]. 北京: 北京科技大學, 2017 Li Z Z. Investigations on Fundamental Theory of CO₂ Applied in Steelmaking Processes [Dissertation]. Beijing: University of Science and Technology Beijing, 2017
[22]	李智崢, 朱榮, 朱益強. CO₂對脫磷轉爐物料和能量的影響. 工程科學學報, 2016, 38(增刊1): 232 Li Z Z, Zhu R, Zhu Y Q. Effect of CO₂ on material and energy in dephosphorization converters. Chin J Eng, 2016, 38(Suppl 1): 232
[23]	郭漢杰. 冶金物理化學教程. 2版. 冶金工業出版社, 2006 Guo H J. Metallurgical Physical Chemistry Course. 2nd Ed. Beijing: Metallurgical Industry Press, 2006
[24]	武珣, 包燕平, 岳峰, 等. 影響轉爐終點碳氧積的因素分析. 鋼鐵研究, 2010, 38(2):26 Wu X, Bao Y P, Yue F, et al. Study on factors to affect the product of carbon content and oxygen content at blowing end-point of BOF steelmaking. Res Iron Steel, 2010, 38(2): 26
[25]	戰東平, 邱國興, 牛奔, 等. 氮在鋼液中溶解的熱力學及動力學研究. 煉鋼, 2015, 31(5):7 Zhan D P, Qiu G X, Niu B, et al. Thermodynamics and kinetics research of nitrogen dissolution in steel. Steelmaking, 2015, 31(5): 7