Effect of cerium on welding performance of 700 MPa high-strength steel used in construction machinery
-
摘要: 針對工業生產700 MPa級高強度調質態鋼板，通過Gleeble3500熱模擬機進行模擬焊接試驗，利用光學顯微鏡、硬度儀、場發射掃描電鏡等設備對比研究了稀土Ce對高強鋼焊接熱影響區（HAZ）顯微組織、晶粒度和力學性能的影響。研究結果表明，焊接熱輸入為25 kJ·cm?1和50 kJ·cm?1時，無稀土鋼焊接熱影響區沖擊功分別為84.8 J和24.5 J，Ce質量分數為0.0018%的鋼焊接熱影響區沖擊功分別為110.0 J和112.0 J，因此鋼中加入適量Ce能夠有效改善鋼板焊接韌性。對比分析兩種實驗鋼焊接熱影響區晶粒尺寸和顯微組織可以看出，隨著焊接熱輸入值增大，高強鋼焊接熱影響區顯微組織均逐漸從馬氏體、下貝氏體轉變為上貝氏體和粒狀貝氏體組織，且奧氏體晶粒尺寸明顯增大。但相同焊接熱輸入下，含Ce鋼焊接熱影響區晶粒尺寸顯著減小，組織更加細小，且脆性的上貝氏體組織減少，從而顯著提高了700 MPa級高強鋼的焊接性能。
-
關鍵詞:
- 稀土 /
- 焊接熱影響區 /
- 氧化物冶金 /
- 700 MPa級高強鋼 /
- 沖擊性能
Abstract: As the use of high-strength thick plates is increasing in marine engineering, bridge engineering, petroleum pipelines, and other fields, the required performance level of thick welded plates is also increasing. Oxide metallurgy technology, which is used to improve the toughness of heat-affected zones by controlling the formation and dispersion of high-melting-temperature oxide particles in steel, has attracted increasing attention by researchers in recent years. The effect of cerium on the welding performance of industrial quenched and tempered high-strength steel was investigated. Using a Gleeble 3500 thermal simulator, the coarse-grained heat-affected zones of high-strength steel were simulated with different cerium contents. The microstructures, austenite grains, and mechanical properties of the heat-affected zone were investigated by using optical microscopy, scanning electron microscopy equipped with energy dispersive spectrometry, and hardness testing. The results show that when the heat inputs are 25 kJ·cm?1 and 50 kJ·cm?1, the impact energies of the heat-affected zone of Ce-undoped steel are 84.8 J and 24.5 J, respectively. When the mass fraction of Ce is 0.0018%, the impact energies of the heat-affected zone are 110.0 J and 112.0 J, respectively. The different degrees of toughness of the two experimental steels indicate that the appropriate content of rare earth element can effectively improve welding performance. By comparing and analyzing the microstructures and prior-austenite grain sizes of the two experimental steels, it can be seen that with increases in the welding heat input, the microstructure of the heat-affected zone of the high-strength steel gradually transforms from martensite and lower bainite to upper bainite and granular bainite, and the average size of the prior-austenite grains in the heat-affected zone obviously increases. However, at the same welding heat input, the size of the prior-austenite grains in the heat-affected zone of Ce-doped high-strength steel is significantly smaller. The observed microstructure of Ce-doped steel is finer with a reduced content of brittle upper bainite, which significantly improves the welding performance of 700 MPa high-strength steel.-
Key words:
- rare earth /
- heat-affected zone /
- oxide metallurgy /
- 700 MPa high-strength steel /
- toughness
-
圖 1 鋼A不同焊接熱輸入試樣焊接熱影響區顯微組織。（a） 25 kJ·cm?1；（b） 50 kJ·cm?1；（c） 75 kJ·cm?1；（d） 100 kJ·cm?1
Figure 1. Microstructures in HAZ of sample A after welding simulation: (a) 25 kJ·cm?1; (b) 50 kJ·cm?1; (c) 75 kJ·cm?1; (d) 100 kJ·cm?1
圖 2 鋼B不同焊接熱輸入試樣焊接熱影響區顯微組織。（a） 25 kJ·cm?1；（b） 50 kJ·cm?1；（c） 75 kJ·cm?1；（d） 100 kJ·cm?1
Figure 2. Microstructures in HAZ of sample B after welding simulation: (a) 25 kJ·cm?1; (b) 50 kJ·cm?1; (c) 75 kJ·cm?1; (d) 100 kJ·cm?1
圖 3 鋼A不同焊接熱輸入試樣焊接熱影響區原奧氏體晶粒照片。（a） 25 kJ·cm?1；（b） 50 kJ·cm?1
Figure 3. Prior-austenite grains in HAZ of sample A after welding simulation: (a) 25 kJ·cm?1; (b) 50 kJ·cm?1
圖 4 鋼B不同焊接熱輸入試樣焊接熱影響區原奧氏體晶粒照片。（a） 25 kJ·cm?1；（b） 50 kJ·cm?1
Figure 4. Prior-austenite grains in HAZ of sample B after welding simulation: (a) 25 kJ·cm?1; (b) 50 kJ·cm?1
圖 6 無稀土時高強鋼凝固過程中V、Nb、Ti和Al的碳氮化物計算
Figure 6. Calculations of carbonitrides of V, Nb, Ti, and Al of high-strength steel without addition of cerium
圖 7 凝固過程夾雜物析出計算。（a）鋼A；（b）鋼B
Figure 7. Calculated inclusion precipitations: (a) steel A; (b) steel B
圖 8 鋼B試樣夾雜物分析（焊接熱輸入為25 kJ·cm?1）。 （a） 晶界上的黑色小洞；（b） 晶界上的稀土夾雜物
Figure 8. Inclusions in HAZ of sample B (25 kJ·cm?1 of heat input): (a) holes in grain boundaries observed; (b) rare earth inclusions in grain boundaries
圖 9 實驗鋼不同熱輸入下室溫沖擊功
Figure 9. HAZ impact energy at different heats input of experimental steels
圖 10 實驗鋼不同熱輸入下焊接熱影響區硬度
Figure 10. HAZ hardness values at different heat inputs of experimental steels
表 1 實驗鋼化學成分（質量分數）
Table 1. Chemical composition of experimental steels
% Sample C Si Mn P Al Nb V O Sample A 0.12 0.32 1.60 0.014 0.024 0.047 0.066 0.0012 Sample B 0.12 0.37 1.70 0.014 0.027 0.048 0.069 0.0016 Sample Cr Mo Ca Mg Ce Ti S N Sample A 0.284 0.130 0.0017 0.0004 0 0.017 0.0019 0.0030 Sample B 0.300 0.130 0.0012 0.0005 0.0018 0.017 0.0030 0.0037 
下載: 導出CSV
表 2 實驗鋼母材力學性能
Table 2. Mechanical properties of experimental steels
ReL/MPa Rm/MPa A/% Akv/J Average value of Akv/J Sample A 794 799 832 830 14.5 15.0 213 213 220 216 Sample B 803 800 840 843 14.0 14.5 181 209 227 205 Note: ReL—yield strength, Rm—tensile strength, A—elongation, Akv—impact energy at ?20 ℃.
下載: 導出CSV
259luxu-164<th id="5nh9l"></th> <strike id="5nh9l"></strike> <th id="5nh9l"><noframes id="5nh9l"><th id="5nh9l"></th> <strike id="5nh9l"></strike> <th id="5nh9l"><noframes id="5nh9l"> <th id="5nh9l"></th> <strike id="5nh9l"><noframes id="5nh9l"><span id="5nh9l"></span> <span id="5nh9l"><noframes id="5nh9l"><span id="5nh9l"></span> <strike id="5nh9l"><noframes id="5nh9l"><strike id="5nh9l"></strike> <span id="5nh9l"><noframes id="5nh9l"> <span id="5nh9l"><noframes id="5nh9l"> <span id="5nh9l"></span> <span id="5nh9l"><video id="5nh9l"></video></span> <th id="5nh9l"><noframes id="5nh9l"><th id="5nh9l"></th> -
參考文獻
[1] Lou H N, Wang C, Wang B X, et al. Effect of Ti–Mg–Ca treatment on properties of heat-affected zone after high heat input welding. J Iron Steel Res Int, 2019, 26(5): 501 doi: 10.1007/s42243-018-0091-6 [2] Lu J L, Cheng G G, Tan B, et al. Effect of Zr, Al addition on characteristics of MnS and formation of intragranular ferrite in non-quenched and tempered steel. ISIJ Int, 2018, 58(5): 921 doi: 10.2355/isijinternational.ISIJINT-2017-617 [3] Wan X L, Wu K M, Huang G, et al. In situ observations of the formation of fine-grained mixed microstructures of acicular ferrite and bainite in the simulated coarse-grained heated-affected zone. Steel Res Int, 2014, 85(2): 243 doi: 10.1002/srin.201200313 [4] Genichi S. Progress of high performance steel plates with excellent HAZ toughness. Nippon Steel Sumitomo Met Techl Rep, 2018, 119: 22 [5] Kazuhiro F, Ken-ichi Y, Yasuhiro S, et al. High strength TMCP steel plate for offshore structure with excellent HAZ toughness at welded joints. Nippon Steel Sumitomo Met Techl Rep, 2015, 110: 43 [6] Nakashima K, Hase K, Endo S, et al. Development of YP390MPa steel plate for shipbuilding with superior low temperature toughness for large heat input welding // The Twenty-fourth International Ocean and Polar Engineering Conference. Busan, 2014: ISOPE-I-14-569 [7] Ichimiya K, Hase K, Endo S, et al. Offshore structural steel plates for extreme low temperature service with excellent HAZ toughness // Proceedings of the ASME 2014 33rd International Conference on Ocean, Offshore and Arctic Engineering. San Francisco, 2014: V005T03A027 [8] Ichimiya K, Hase K, Endo S, et al. Steel plates with excellent HAZ toughness for offshore structure // Proceedings of the ASME 2013 32nd International Conference on Ocean, Offshore and Arctic Engineering. Nantes, 2013: V003T03A021 [9] Kato T, Sato S, Ohta H, et al. Effects of Ca addition on formation behavior of TiN particles and HAZ toughness in large-heat-input welding. Kobelco Technol Rev, 2011, 30: 76 [10] Chen X, Bu Y, Xi T H. Progress on research and development of large heat input welding steel series in WISCO. Mater China, 2011, 30(12): 34陳曉, 卜勇, 習天輝. 武鋼大線能量焊接系列鋼的研發進展. 中國材料進展, 2011, 30(12):34 [11] Xu L Y, Yang J, Wang R Z, et al. Effect of Mg addition on formation of intragranular acicular ferrite in heat-affected zone of steel plate after high-heat-input welding. J Iron Steel Res Int, 2018, 25(4): 433 doi: 10.1007/s42243-018-0054-y [12] Shi M H, Yuan X G, Huang H J, et al. Effect of Zr addition on the microstructure and toughness of coarse-grained heat-affected zone with high-heat input welding thermal cycle in low-carbon steel. J Mater Eng Perform, 2017, 26(7): 3160 doi: 10.1007/s11665-017-2758-8 [13] Xu L Y, Yang J, Wang R Z, et al. Effect of welding heat input on microstructure and toughness of heated-affected zone in steel plate with Mg deoxidation. Steel Res Int, 2017, 88(12): 1700157 doi: 10.1002/srin.201700157 [14] Pan F, Zhang J, Chen H L, et al. Effects of rare earth metals on steel microstructures. Materials, 2016, 9(6): 417 doi: 10.3390/ma9060417 [15] Xin W B, Song B, Song M M, et al. Effect of cerium on characteristic of inclusions and grain boundary segregation of arsenic in iron melts. Steel Res Int, 2015, 86(12): 1430 doi: 10.1002/srin.201400332 [16] Liu H L, Liu C J, Jiang M F. Effect of rare earths on impact toughness of a low-carbon steel. Mater Des, 2012, 33: 306 doi: 10.1016/j.matdes.2011.06.042 [17] Chang L Z, Gao G, Zheng F Z, et al. Effect of rare earth and magnesium complex treatment on inclusions in GCr15 bearing steel. Chin J Eng, 2019, 41(6): 763常立忠, 高崗, 鄭福舟, 等. 稀土-鎂復合處理對GCr15軸承鋼中夾雜物的影響. 工程科學學報, 2019, 41(6):763 [18] Thewlis G. Effect of cerium sulphide particle dispersions on acicular ferrite microstructure development in steels. Mater Sci Technol, 2006, 22(2): 153 doi: 10.1179/026708306X81432 [19] Yu S F, Yan N, Chen Y. Inclusions and microstructure of Ce-added weld metal coarse grain heat-affected zone in twin-wire submerged-arc welding. J Mater Eng Perform, 2016, 25(6): 2445 doi: 10.1007/s11665-016-2069-5 [20] Yan H H, Hu Y, Zhao D W. The influence of rare earth elements on phase transformation in 25Mn steel during continuous heating. Metall Mater Trans A, 2018, 49(11): 5271 doi: 10.1007/s11661-018-4891-x [21] Li Y D, Liu C J, Li C L, et al. A coupled thermodynamic model for prediction of inclusions precipitation during solidification of heat-resistant steel containing cerium. J Iron Steel Res Int, 2015, 22(6): 457 doi: 10.1016/S1006-706X(15)30027-3 [22] Lin Q, Ye W, Li S L. Rare earth dissolved in solid solution of steel and its effect micro structures. J Chin Soc Rare Earths, 1989, 7(2): 54 doi: 10.3321/j.issn:1000-4343.1989.02.012林勤, 葉文, 李栓祿. 鋼中稀土固溶規律及作用研究. 中國稀土學報, 1989, 7(2):54 doi: 10.3321/j.issn:1000-4343.1989.02.012 [23] Gao J Z, Fu P X, Liu H W, et al. Effects of rare earth on the microstructure and impact toughness of H13 steel. Metals, 2015, 5(1): 383 doi: 10.3390/met5010383 [24] Zhao W X, Wu Y, Jiang S H, et al. Micro-alloying effects of yttrium on recrystallization behavior of an alumina-forming austenitic stainless steel. J Iron Steel Res Int, 2016, 23(6): 553 doi: 10.1016/S1006-706X(16)30087-5 [25] Tomita Y. Effect of microstructure on plane-strain fracture toughness of AISI 4340 steel. Metall Mater Trans A, 1988, 19(10): 2513 doi: 10.1007/BF02645479 -
點擊查看大圖
計量
- 文章訪問數: 1602
- HTML全文瀏覽量: 737
- PDF下載量: 87
- 被引次數: 0
