無煙煤制備高性能鋰離子電池負極材料的研究

王晶晶; 趙洪亮; 胡韜; 劉風琴

doi:10.13374/j.issn2095-9389.2019.07.11.005

無煙煤制備高性能鋰離子電池負極材料的研究

doi: 10.13374/j.issn2095-9389.2019.07.11.005

1.
北京科技大學冶金與生態工程學院，北京 100083
2.
安徽新衡新材料科技有限公司，馬鞍山 243071

基金項目: 中國工程院院地合作資助項目（2019NXZD5）

詳細信息

通訊作者:
E-mail：liufq@ustb.edu.cn

中圖分類號: TM912.9
計量
- 文章訪問數: 1631
- HTML全文瀏覽量: 1100
- PDF下載量: 82
- 被引次數: 0
出版歷程
- 收稿日期: 2019-07-11
- 刊出日期: 2020-07-01

High-performance anode materials based on anthracite for lithium-ion battery applications

1.
School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing 100083, China
2.
Anhui Xinheng New Materials Technology Co., Ltd., Maanshan 243071, China

More Information

Corresponding author: E-mail: liufq@ustb.edu.cn

摘要

摘要: 以我國資源豐富的低成本優質無煙煤為原料，經過2800 ℃高溫純化、石墨化處理，制備出鋰電池用負極材料，用相同手段處理商業化石墨的前體石油焦與石墨化無煙煤作對比。通過X射線衍射（XRD），掃描電子顯微鏡（SEM），透射電子顯微鏡（TEM），拉曼光譜（Roman）和氮吸附?解吸等手段對無煙煤基負極材料進行微觀結構的表征。采用恒流充放電（GCD），循環伏安（CV）表征其電化學性能。實驗結果表明，無煙煤基石墨化負極材料的石墨化度可達95.44%，比表面積為1.1319 m²·g^?1，石墨片層結構平整光滑。該石墨化無煙煤作為鋰離子電池的負極材料首次庫倫效率為87%，在0.1C的電流密度下具有345.3 mA·h·g^?1的可逆容量，且在高倍率下該材料比石墨化石油焦材料顯現出更好儲鋰性能，這歸功于石墨化無煙煤較為規則高度有序的表面結構。在不同倍率循環后電流密度恢復到0.1C時容量基本無衰減，100圈循環后可逆容量保持率高達93.8%，基本與石墨化石油焦負極相當，擁有優異的循環穩定性。無煙煤基石墨在容量、倍率性能及循環穩定性上基本接近甚至超過石墨化石油焦。本研究表明，采用優質無煙煤作為原料生產鋰離子電池負極材料具有潛在的研究價值和廣闊的商業前景。
- 無煙煤 /
- 高溫石墨化 /
- 負極材料 /
- 高石墨化度 /
- 鋰離子電池
Abstract: The rise in the price of petroleum coke and needle coke, which are used as anode materials of lithium-ion batteries, has revealed the difficulty of the industry in finding high-performance and low-cost alternatives of these raw materials. In this study, anthracite, a low-cost, high-quality raw material, of which China is rich in resources, was used. After a 2800 °C purification and graphitization treatment, the anode material for lithium battery was prepared. Petroleum coke, as the precursor of commercial graphite, was treated using the same method that was being used for graphitized anthracite, for comparison reasons. The microstructure of anthracite-based anode materials was characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Raman spectroscopy (Roman), and nitrogen adsorption-desorption. Cyclic voltammetry (CV) was used to characterize the electrochemical performance of anthracite-based anode materials by applying constant current charge and discharge (GCD). The experimental results show that the graphitization degree of anthracite-based graphitized anode material can reach 95.44%, with the specific surface area being 1.1319 m²·g^?1, and the graphite sheet structure is found to be smooth. The graphitized anthracite, as the anode material of a lithium-ion battery, has a first coulombic efficiency of 87% and a reversible capacity of 345.3 mA·h·g^?1 at a current rate of 0.1C, and the material has better lithium storage performance than graphitized petroleum coke material at a high rate. The relatively highly ordered surface structure of graphitized anthracite leads to a better storage performance of lithium. When the current rate returns to 0.1C after different current rates, the capacity has basically no attenuation. After 100 cycles, the reversible capacity retention rate is as high as 93.8%, which is basically equivalent to the rate of graphitized petroleum coke anode while the graphitized anthracite also shows excellent cycle stability. Anthracite-based graphite is equivalent or even superior to graphitized petroleum coke in terms of capacity, rate performance, and cycle stability. This study shows that the use of high-quality anthracite as raw material for the production of lithium-ion battery anode materials has a potential research value and broad commercial prospects.
- anthracite /
- high temperature graphitization /
- anode materials /
- high graphitization degree /
- lithium-ion battery

HTML全文

圖 1 無煙煤和石油焦及其石墨化后的微觀形貌圖。（a）無煙煤前體；（b，c，d）GA樣品掃描電鏡圖；（e）石油焦前體；（f，g，h）GPC樣品掃描電鏡圖

Figure 1. Microscopic topography of anthraciteand petroleum coke after graphitization: (a) anthracite precursor; (b, c, d) GA sample; (e) petroleum coke precursor; (f，g，h) scanning electron micrograph of GPC sample

下載: 全尺寸圖片幻燈片

圖 2 GA樣品透射電鏡圖。（a，b）透射電鏡；（c，d）高倍透射電鏡

Figure 2. Transmission electron micrograph of GA sample: (a, b) TEM; (c, d) HRTEM

下載: 全尺寸圖片幻燈片

圖 3 無煙煤和GA樣品的X射線衍射圖

Figure 3. XRD pattern of anthracite and GA samples

下載: 全尺寸圖片幻燈片

圖 4 無煙煤和GA樣品的拉曼光譜圖

Figure 4. Raman spectra of anthracite and GA samples

下載: 全尺寸圖片幻燈片

圖 5 GA和GPC樣品的吸附曲線及孔徑分布情況。（a）GA的氮氣吸附?解吸等溫線；（b）GA的孔徑分布曲線；（c）GPC的氮氣吸附?解吸等溫線；（d）GPC的孔徑分布曲線

Figure 5. Adsorption curve and pore size distribution of GA and GPC sample: (a) nitrogen adsorption-desorption isotherm of GA; (b) pore size distribution curve of GA; (c) nitrogen adsorption-desorption isotherm of GPC; (d) pore size distribution curve of GPC

下載: 全尺寸圖片幻燈片

圖 6 GA和GPC不同倍率充放電曲線。（a）0.1C～1C倍率下GA的充放電曲線；（b）0.1C～1C倍率下GPC的充放電曲線

Figure 6. Charge and discharge curves of GA and GPC at different magnifications: (a) charge and discharge curves of GA at 0.1C–1C rate; (b) charge and discharge curves of GPC at 0.1C–1C rate

下載: 全尺寸圖片幻燈片

圖 7 GA和GPC的倍率曲線及循環伏安曲線。（a）0.1C～1C倍率下GA和GPC的倍率曲線；（b）GA的循環伏安掃描曲線

Figure 7. Magnification curve and cyclic voltammetry curve of GA and GPC: (a) magnification curve of GA and GPC at 0.1C–1C rate; (b) cyclic voltammetric curve of GA

下載: 全尺寸圖片幻燈片

圖 8 GA和GPC的循環性能和庫倫效率

Figure 8. Cyclic performance and Coulombic efficiency of GA and GPC

下載: 全尺寸圖片幻燈片

表 1 實驗藥品和試劑

Table 1. Experimental samples and reagents

Reagent name	Chemical formula	Reagent grade	Supplier
Polyvinylidene fluoride（PVDF）	[?CH₂?CF₂?]	Premium grade	CALB Co., Ltd.
N-methylpyrrolidone（NMP）	C₅H₉NO	Electronic grade	Shanghai Titan Technology Co., Ltd.
Electrolyte	LiPF₆	Electronic grade	BAK Battery Co., Ltd.
Acetylene carbon black（Super-P）	C	Electronic grade	Mitsubishi Chemical Co., Ltd.

下載: 導出CSV

表 2 石墨化無煙煤灼燒數據

Table 2. Graphitized anthracite burning data

Number	Net weight of crucible, m₁/g	Sample quality, m₂/g	Total mass after burning, m₃/g	Ash, (m₃?m₁)·m₂^?1/%
1	17.1098	1.5137	17.1140	0.277
2	17.0690	1.5553	17.0732	0.270
3	16.7645	1.0415	16.7674	0.278
4	16.9199	1.0513	16.9229	0.275

下載: 導出CSV

表 3 GA和GPC的首次充放電容量和庫倫效率

Table 3. First charge and discharge capacity and coulombic efficiency of GA and GPC

Sample name	First discharge capacity/(mA·h·g^?1)	First charge capacity/(mA·h·g^?1)	Irreversible capacity/(mA·h·g^?1)	Coulombic efficiency/%
GA	415.4	361.4	54	87
GPC	395.8	346.3	49.5	87.5

下載: 導出CSV

259luxu-164

參考文獻(19)

[1]	Griffiths G. Review of developments in lithium secondary battery technology. Underwater Technol, 2016, 33(3): 153 doi: 10.3723/ut.33.153
[2]	Mekonnen Y, Sundararajan A, Sarwat A I. A review of cathode and anode materials for lithium-ion batteries//SoutheastCon 2016. Norfolk, 2016: 1
[3]	Nitta N, Wu F X, Lee J T, et al. Li-ion battery materials: present and future. Mater Today, 2015, 18(5): 252 doi: 10.1016/j.mattod.2014.10.040
[4]	Mahmood N, Tang T Y, Hou Y L. Nanostructured anode materials for lithium ion batteries: progress, challenge and perspective. Adv Energy Mater, 2016, 6(17): 1600374 doi: 10.1002/aenm.201600374
[5]	Kim Y J, Yang H, Yoon S H, et al. Anthracite as a candidate for lithium ion battery anode. J Power Sources, 2003, 113(1): 157 doi: 10.1016/S0378-7753(02)00528-1
[6]	Cameán I, Lavela P, Tirado J L, et al. On the electrochemical performance of anthracite-based graphite materials as anodes in lithium-ion batteries. Fuel, 2010, 89(5): 986 doi: 10.1016/j.fuel.2009.06.034
[7]	Zhou X Y, Ma L L, Yang J, et al. Properties of graphitized boron-doped coal-based coke powders as anode for lithium-ion batteries. J Electroanal Chem, 2013, 698: 39 doi: 10.1016/j.jelechem.2013.03.019
[8]	Xing B L, Zhang C T, Cao Y J, et al. Preparation of synthetic graphite from bituminous coal as anode materials for high performance lithium-ion batteries. Fuel Process Technol, 2018, 172: 162 doi: 10.1016/j.fuproc.2017.12.018
[9]	Xiao J, Li F C, Zhong Q F, et al. Effect of high-temperature pyrolysis on the structure and properties of coal and petroleum coke. J Anal Appl Pyrol, 2016, 117: 64 doi: 10.1016/j.jaap.2015.12.015
[10]	Liu X X, Luo J, Zhu Y T, et al. Removal of methylene blue from aqueous solutions by an adsorbent based on metal-organic framework and polyoxometalate. J Alloys Compd, 2015, 648: 986 doi: 10.1016/j.jallcom.2015.07.065
[11]	Tian B, Li P F, Li D W, et al. Preparation of micro-porous monolithic activated carbon from anthracite coal using coal tar pitch as binder. J Porous Mater, 2017, 25(4): 1
[12]	Wu X, Yang X L, Zhang F, et al. Carbon-coated isotropic natural graphite spheres as anode material for lithium-ion batteries. Ceram Int, 2017, 43(12): 9458 doi: 10.1016/j.ceramint.2017.04.123
[13]	H?gstr?m K C, Malmgren S, Hahlin M, et al. The buried carbon/solid electrolyte interphase in Li-ion batteries studied by hard X-ray photoelectron spectroscopy. Electrochim Acta, 2014, 138: 430 doi: 10.1016/j.electacta.2014.06.129
[14]	Ramos A, Cameán I, Cuesta N, et al. Graphitized stacked-cup carbon nanofibers as anode materials for lithium-ion batteries. Electrochim Acta, 2014, 146: 769 doi: 10.1016/j.electacta.2014.09.035
[15]	Tian M, Wang W, Liu Y, et al. A three-dimensional carbon nano-network for high performance lithium ion batteries. Nano Energy, 2015, 11: 500 doi: 10.1016/j.nanoen.2014.11.006
[16]	Verma P, Maire P, Novák P. A review of the features and analyses of the solid electrolyte interphase in Li-ion batteries. Electrochim Acta, 2010, 55(22): 6332 doi: 10.1016/j.electacta.2010.05.072
[17]	Jung K N, Pyun S I. Effect of pore structure on anomalous behaviour of the lithium intercalation into porous V₂O₅ film electrode using fractal geometry concept. Electrochim Acta, 2006, 51(13): 2646 doi: 10.1016/j.electacta.2005.08.008
[18]	Cameán I, Garcia A B. Graphite materials prepared by HTT of unburned carbon from coal combustion fly ashes: Performance as anodes in lithium-ion batteries. J Power Sources, 2011, 196(10): 4816 doi: 10.1016/j.jpowsour.2011.01.041
[19]	Wang C, Zhao H, Wang J, et al. Electrochemical performance of modified artificial graphite as anode material for lithium ion batteries. Ionics, 2013, 19(2): 221