鋁熱法冶煉釩鐵渣的熔化性能

曹敏; 宋波; 宋明明; 劉豐強; 陳煉

doi:10.13374/j.issn1001-053x.2014.02.004

鋁熱法冶煉釩鐵渣的熔化性能

doi: 10.13374/j.issn1001-053x.2014.02.004

曹敏^1,2,
宋波^1,2, ,,
宋明明^1,2,
劉豐強³,
陳煉⁴

1. 北京科技大學鋼鐵冶金新技術國家重點實驗室, 北京 100083;
2 北京科技大學冶金與生態工程學院, 北京 100083;
3. 攀鋼集團釩業有限公司, 攀枝花 617023;
4. 攀鋼集團研究院有限公司釩鈦資源綜合利用國家重點實驗室, 攀枝花 617000

基金項目:

中央高校基本科研業務費專項資金資助項目（FRF-SD-12-002B，FRF-SD-12-010A）；國家自然科學基金資助項目（51234001）

詳細信息

通訊作者:
宋波,E-mail:songbo@metall.ustb.edu.cn

中圖分類號: TF61
計量
- 文章訪問數: 283
- HTML全文瀏覽量: 117
- PDF下載量: 10
- 被引次數: 0
出版歷程
- 收稿日期: 2012-11-28
- 網絡出版日期: 2021-07-10

Melting performance of the slag system from FeV alloy production by thermit method

CAO Min^1,2,
SONG Bo^{1,2
, ,},
SONG Ming-ming^1,2,
LIU Feng-qiang³,
CHEN Lian⁴

1. State Key Laboratory of Advanced Metallurgy, University of Science and Technology Beijing, Beijing 100083, China;
2. School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing 100083, China;
3. Pangang Group Vanadium Industry Co. Ltd., Panzhihua 617023, China;
4. State Key Laboratory of Vanadium and Titanium Resources Comprehensive Utilization, Pangang Group Research Institute Co. Ltd., Panzhihua 617000, China

摘要

摘要: 采用熱力學軟件FactSage中的Equilib和Phase Diagram模塊分別對Al₂O₃-CaO-MgO三元渣系的熔化性能及添加助熔劑后對渣系熔點的影響進行理論分析，并實驗測定渣系的實際熔點.發現渣系熔點隨w（Al₂O₃）/w（CaO）比的升高先降低后升高，w（MgO）為4%～5%時渣系熔點最低.對于w（Al₂O₃）/w（MgO）>3的渣系，w（CaO）<30%時渣系熔點隨w（CaO）增加而降低.2<w（Al₂O₃）/w（CaO）<2.5，w（MgO）為15%～18%時，釩鐵渣中加2.29%AlCl₃、4.86% Fe₂O₃或4.77% Na₂O時均可降低原渣熔化性溫度約100℃.
- 釩鐵合金 /
- 渣 /
- 鋁熱法 /
- 熔點 /
- 熱力學
Abstract: The melting performance of an Al₂O₃-CaO-MgO ternary slag system and the effect of added fluxes on the melting point of the slag system were theoretically analyzed by using Equilib and Phase Diagram modules in thermodynamic software FactSage. The melting temperature of the slag system from production was measured. It is found that the melting point of the slag system decreases first and then increases with increasing w(Al₂O₃)/w(CaO) ratio, and it reaches the lowest value when w(MgO) is 4% to 5%. At the w (Al₂O₃)/w(MgO) ratio more than 3 and w(CaO) less than 30%, the melting point decreases with increasing w(CaO). When 2〈w (Al₂O₃)/w(CaO) 〈2.5 and w(MgO) is 15% to 18%, the melting point can decrease about 100℃ with the addition of 2.29% AlCl₃, 4.86% Fe₂O₃ or 4.77% Na₂O in the slag system.
- iron vanadium alloys /
- slags /
- thermit method /
- melting point /
- thermodynamics